Warhammer Magnet Size Guide
Model Size Glossary
Base Sizes
Below is a guide listing common model base sizes and the specific models typically associated with each.
This should cover most of the common base sizes and model types, however, if you are using models from specialized or limited-release sets, you may need to check those specific models for any unique base sizes. The size magnet or steel disc you need is specific to your application and the strength you require.
Base sizes and the typically recommended magnet sizes:
| MODEL | BASE SIZE | SUITABLE MAGNETS SIZES | |
| DISCIPLES OF TZEENTCH | |||
| Blue Horrors of Tzeentch | 25mm |
4mm x 2mm: Works well for infantry. (Stack 2pcs of 4mm x 1mm) 5mm x 2mm: Alternative for better stability. 6mm x 2mm or 3mm: Suitable for most standard bases. |
|
| Brimstone Horrors of Tzeentch | 25mm |
4mm x 2mm: Works well for infantry. (Stack 2pcs of 4mm x 1mm) 5mm x 2mm: Alternative for better stability. 6mm x 2mm or 3mm: Suitable for most standard bases. |
|
| Burning Chariots of Tzeentch | 120 x 92mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Curseling, Eye of Tzeentch | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Exalted Flamers of Tzeentch | 75 x 42mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Exalted Greater Daemon of Tzeentch | 130mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Eyes of the Nine | 32mm (Horrors are 25mm) | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Fatemaster | 60mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. |
|
| Flamers of Tzeentch | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Gaunt Summoner (and Chaos Familiars) | 40mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. |
|
| Gaunt Summoner of Tzeentch | 40mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. |
|
| Gaunt Summoner’s Chaos Familiars | 25mm |
4mm x 2mm: Works well for infantry. (Stack 2pcs of 4mm x 1mm) 5mm x 2mm: Alternative for better stability. 6mm x 2mm or 3mm: Suitable for most standard bases. |
|
| Herald of Tzeentch | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Herald of Tzeentch on Burning Chariot | 120 x 92mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Herald of Tzeentch on Disc | 60mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. |
|
| Kairic Acolytes | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| BLADES OF KHORNE | |||
| Lord of Khorne on Juggernaut | 90 x 52mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Magore’s Fiends | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Mazarall the Butcher | 100mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Mighty Lord of Khorne | 60mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. |
|
| Mighty Skullcrushers | 90 x 52mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Riptooth | 50mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Scyla Anfingrimm | 60mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. |
|
| Skaarac the Bloodborn | 160mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Skarbrand | 100mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Skarr Bloodwrath | 40mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. |
|
| Skull Cannons | 120 x 92mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Skullgrinder | 40mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. |
|
| Skullmaster, Herald of Khorne | 90 x 52mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Skullreapers | 40mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. |
|
| Skulltaker | 40mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. |
|
| Slaughterbrute of Khorne | 120 x 92mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Slaughterpriest | 40mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. |
|
| Slaughterpriest with Hackblade and Wrath-hammer | 40mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. |
|
| Valkia the Bloody | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Wrath of Khorne Bloodthirster | 120 x 92mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Wrath-axe | 105 x 70mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Wrathmongers | 40mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. |
|
| BEASTS OF CHAOS | |||
| Beastlord | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Bestigors | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Bullgors | 50mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Centigors | 60 x 35mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. |
|
| Chaos Gargant | 90 x 52mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Chaos Warhounds | 60 x 35mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. |
|
| Chimera | 120 x 92mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Cockatrice | 60mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. |
|
| Cygor | 120 x 92mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Doomblast Dirgehorn | 40mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. |
|
| Doombull | 50mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Dragon Ogor Shaggoth | 90 x 52mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Dragon Ogors | 90 x 52mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Ghorgon | 120 x 92mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Gors | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Great Bray-Shaman | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Jabberslythe | 120 x 92mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Ravening Direflock | 40mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. |
|
| Razorgors | 75 x 42mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Tuskgor Chariots | 105 x 70mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Ungor Raiders | 25mm |
4mm x 2mm: Works well for infantry. (Stack 2pcs of 4mm x 1mm) 5mm x 2mm: Alternative for better stability. 6mm x 2mm or 3mm: Suitable for most standard bases. |
|
| Ungors | 25mm | 4mm x 2mm: Works well for infantry. (Stack 2pcs of 4mm x 1mm) 5mm x 2mm: Alternative for better stability. 6mm x 2mm or 3mm: Suitable for most standard bases. |
|
| Wildfire Taurus | 105 x 70mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| BLADES OF KHORNE | |||
| Aspiring Deathbringer | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Aspiring Deathbringer with Goreaxe and Skullhammer | 40mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. |
|
| Bleeding Icon | 105 x 70mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Blood Throne | 120 x 92mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Blood Warriors | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Bloodcrushers | 90 x 52mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Bloodletters | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Bloodmaster, Herald of Khorne | 40mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. |
|
| Bloodreavers | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Bloodsecrator | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Bloodstoker | 40mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. |
|
| Bloodthirster of Insensate Rage | 120 x 92mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Bloodthirster of Unfettered Fury | 120 x 92mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Exalted Deathbringer with Bloodbite Axe | 40mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. |
|
| Exalted Deathbringer with Impaling Spear | 40mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. |
|
| Exalted Deathbringer with Ruinous Axe | 40mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. |
|
| Exalted Greater Daemon of Khorne | 160mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Flesh Hounds | 60 x 35mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. |
|
| Garrek’s Reavers | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Hexgorger Skulls | 60mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. |
|
| Karanak | 75 x 42mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Khorgoraths | 90 x 52mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Korghos Khul | 60mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. |
|
| DAEMONS OF CHAOS | |||
| Be’lakor, Chaos Daemon Prince | 60mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. |
|
| Daemon Prince | 60mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. |
|
| Furies | 25mm |
4mm x 2mm: Works well for infantry. (Stack 2pcs of 4mm x 1mm) 5mm x 2mm: Alternative for better stability. 6mm x 2mm or 3mm: Suitable for most standard bases. |
|
| Soul Grinder | 160mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| LEGION OF AZGORH | |||
| Bull Centaur Renders | 90 x 52mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Bull Centaur Taur’ruk | 90 x 52mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Daemonsmith | 25mm |
4mm x 2mm: Works well for infantry. (Stack 2pcs of 4mm x 1mm) 5mm x 2mm: Alternative for better stability. 6mm x 2mm or 3mm: Suitable for most standard bases. |
|
| Deathshrieker Rocket Launcher | 120 x 92mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Drazhoath the Ashen | 120 x 92mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Dreadquake Mortar | 170mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Infernal Guard Battle Standard Bearer | 25mm |
4mm x 2mm: Works well for infantry. (Stack 2pcs of 4mm x 1mm) 5mm x 2mm: Alternative for better stability. 6mm x 2mm or 3mm: Suitable for most standard bases. |
|
| Infernal Guard Castellan | 25mm | 4mm x 2mm: Works well for infantry. (Stack 2pcs of 4mm x 1mm) 5mm x 2mm: Alternative for better stability. 6mm x 2mm or 3mm: Suitable for most standard bases. |
|
| Infernal Guard Fireglaives | 25mm | 4mm x 2mm: Works well for infantry. (Stack 2pcs of 4mm x 1mm) 5mm x 2mm: Alternative for better stability. 6mm x 2mm or 3mm: Suitable for most standard bases. |
|
| Infernal Guard Ironsworn | 25mm | 4mm x 2mm: Works well for infantry. (Stack 2pcs of 4mm x 1mm) 5mm x 2mm: Alternative for better stability. 6mm x 2mm or 3mm: Suitable for most standard bases. |
|
| Iron Daemon War Engine | 120 x 92mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| K’Daai Fireborn | 50mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Magma Cannon | 120 x 92mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Shar’tor the Executioner | 105 x 70mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Skullcracker War Engine | 120 x 92mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| DISCIPLES OF TZEENTCH | |||
| Kairos Fateweaver | 100mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Lord of Change | 100mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Magister | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Mutalith Vortex Beast of Tzeentch | 120 x 92mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Ogroid Thaumaturge | 50mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Pink Horrors of Tzeentch | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Screamers of Tzeentch | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| The Blue Scribes | 60mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. |
|
| The Changeling | 40mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. |
|
| Tzaangor Enlightened | 40mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. |
|
| Tzaangor Shaman | 40mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. |
|
| Tzaangor Skyfires | 40mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. |
|
| Tzaangors | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Vortemis the All-seeing | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| MAGGOTKIN OF NURGLE | |||
| Beasts of Nurgle | 60mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. |
|
| Bloab Rotspawned | 100mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Epidemius, Tallyman of Nurgle | 60mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. |
|
| Exalted Greater Daemon of Nurgle | 130mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Festus the Leechlord | 40mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. |
|
| Great Unclean One | 130mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Gutrot Spume | 40mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. |
|
| Harbinger of Decay | 75 x 42mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Horticulous Slimux | 105 x 70mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Lord of Afflictions | 60mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. |
|
| Lord of Blights | 40mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. |
|
| Lord of Plagues | 40mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. |
|
| Morbidex Twiceborn | 100mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Nurglings | 40mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. |
|
| Orghotts Daemonspew | 100mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Plague Drones | 60mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. |
|
| Plaguebearers | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Poxbringer, Herald of Nurgle | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Pusgoyle Blightlords | 60mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. |
|
| Putrid Blightkings | 40mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. |
|
| Rotigus | 130mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Sloppity Bilepiper, Herald of Nurgle | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Sorcerer | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Spoilpox Scrivener, Herald of Nurgle | 40mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. |
|
| The Glottkin | 130mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| HEDONITES OF SLAANESH | |||
| Chaos Lord of Slaanesh | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Daemonettes of Slaanesh | 25mm |
4mm x 2mm: Works well for infantry. (Stack 2pcs of 4mm x 1mm) 5mm x 2mm: Alternative for better stability. 6mm x 2mm or 3mm: Suitable for most standard bases. |
|
| Dreadful Visage | 90 x 52mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Exalted Greater Daemon of Slaanesh | 105 x 70mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Exalted Seekers Chariots of Slaanesh | 120 x 92mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Fiends | 75 x 42mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Hellflayers of Slaanesh | 120 x 92mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Hellstriders of Slaanesh | 60 x 35mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. |
|
| Herald of Slaanesh | 25mm |
4mm x 2mm: Works well for infantry. (Stack 2pcs of 4mm x 1mm) 5mm x 2mm: Alternative for better stability. 6mm x 2mm or 3mm: Suitable for most standard bases. |
|
| Herald of Slaanesh on Exalted Seeker Chariot | 120 x 92mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Herald of Slaanesh on Seeker Chariot | 120 x 92mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Infernal Enrapturess | 60 x 35mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. |
|
| Keeper of Secrets | 100mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Lord of Slaanesh on Daemonic Mount | 60mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. |
|
| Mesmerising Mirror | 90 x 52mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Seeker Chariots of Slaanesh | 120 x 92mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Seekers of Slaanesh | 60 x 35mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. |
|
| The Masque of Slaanesh | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| MONSTERS OF CHAOS | |||
| Chaos Siege Gargant | 120 x 92mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Chaos War Mammoth | 280 x 210mm | ||
| Curs’d Ettin | 120 x 92mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Gigantic Chaos Spawn | 100mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Harpies | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Mutalith Vortex Beast | 120 x 92mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Preyton | 60mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. |
|
| Skin Wolves | 60mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. |
|
| Slaughterbrute | 120 x 92mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Warpfire Dragon | 120 x 92mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| SLAVES TO DARKNESS | |||
| Archaon | 160mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Chaos Chariots | 120 x 92mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Chaos Chosen | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Chaos Gorebeast Chariots | 120 x 92mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Chaos Knights | 75 x 42mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Chaos Lord on Daemonic Mount | 75 x 42mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Chaos Lord on Karkadrak | 90 x 52mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Chaos Lord on Manticore | 120 x 92mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Chaos Marauder Horsemen | 60 x 35mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. |
|
| Chaos Marauders | 25mm |
4mm x 2mm: Works well for infantry. (Stack 2pcs of 4mm x 1mm) 5mm x 2mm: Alternative for better stability. 6mm x 2mm or 3mm: Suitable for most standard bases. |
|
| Chaos Sorcerer Lord | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Chaos Sorcerer Lord on Chaos Steed | 75 x 42mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| SLAVES TO DARKNESS | |||
| Chaos Sorcerer Lord on Manticore | 120 x 92mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Chaos Spawn | 50mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Chaos Warriors | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Chaos Warshrine | 120 x 92mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Daemon Prince | 60mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. |
|
| Darkoath Chieftain | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Darkoath Warqueen | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Exalted Hero of Chaos | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Gaunt Summoner of Tzeentch | 40mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. |
|
| The Godsworn Hunt | 32mm (Grawl is 25mm) | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Lord of Chaos | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Nightmaw | 50mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Sayl the Faithless | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Theddra Skull-Scryer | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Varanguard | 75 x 42mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| SKAVEN | |||
| Verminlord Warpseer | 120 x 92mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Vermintide | 120 x 92mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Warlock Bombardier | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Warlock Engineer | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Warp Lightning Cannon | 120 x 92mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Warp Lightning Vortex | 40mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. |
|
| Warp-Grinder | 60 x 35mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. |
|
| Warpfire Thrower | 60 x 35mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. |
|
| Warpgnaw Verminlord | 105 x 70mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Warplock Jezzails | 60 x 35mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. |
|
| TAMURKHAN’S HORDE | |||
| Bile Troggoths | 60mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. |
|
| Daemon Pox Riders of Nurgle | 60mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. |
|
| Daemon Plague Toads of Nurgle | 60mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. |
|
| Kazyk the Befouled | 90 x 52mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Plague Ogors | 60mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. |
|
| Tamurkhan the Maggot Lord | 280 x 210mm | ||
| SKAVEN | |||
| Arch-Warlock | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Bell of Doom | 40mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. |
|
| Brood Horror | 120 x 92mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Clanrats | 25mm |
4mm x 2mm: Works well for infantry. (Stack 2pcs of 4mm x 1mm) 5mm x 2mm: Alternative for better stability. 6mm x 2mm or 3mm: Suitable for most standard bases. |
|
| Clawlord | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Deathmaster | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Doom-Flayer | 60 x 35mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. |
|
| Doomwheel | 105 x 70mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Giant Rats | 25mm |
4mm x 2mm: Works well for infantry. (Stack 2pcs of 4mm x 1mm) 5mm x 2mm: Alternative for better stability. 6mm x 2mm or 3mm: Suitable for most standard bases. |
|
| Grey Seer | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Grey Seer on Screaming Bell | 120 x 92mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Gutter Runners | 25mm |
4mm x 2mm: Works well for infantry. (Stack 2pcs of 4mm x 1mm) 5mm x 2mm: Alternative for better stability. 6mm x 2mm or 3mm: Suitable for most standard bases. |
|
| Hell Pit Abomination | 120 x 92mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Lord Skreech Verminking | 120 x 92mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Master Moulder | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Night Runners | 25mm |
4mm x 2mm: Works well for infantry. (Stack 2pcs of 4mm x 1mm) 5mm x 2mm: Alternative for better stability. 6mm x 2mm or 3mm: Suitable for most standard bases. |
|
| Packmasters | 25mm | 4mm x 2mm: Works well for infantry. (Stack 2pcs of 4mm x 1mm) 5mm x 2mm: Alternative for better stability. 6mm x 2mm or 3mm: Suitable for most standard bases. |
|
| Plague Censer Bearers | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Plague Monks | 25mm |
4mm x 2mm: Works well for infantry. (Stack 2pcs of 4mm x 1mm) 5mm x 2mm: Alternative for better stability. 6mm x 2mm or 3mm: Suitable for most standard bases. |
|
| Plague Priest | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Plague Priest on Plague Furnace | 120 x 92mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Plagueclaw | 120 x 92mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Rat Ogors | 50mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Rat Swarms | 50mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Ratling Gun | 60 x 35mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. |
|
| Skaven Warlord on Brood Horror | 120 x 92mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Skaven Wolf Rats | 75 x 42mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Skritch Spiteclaw | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Skryre Acolytes | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Spiteclaw’s Swarm | 25mm |
4mm x 2mm: Works well for infantry. (Stack 2pcs of 4mm x 1mm) 5mm x 2mm: Alternative for better stability. 6mm x 2mm or 3mm: Suitable for most standard bases. |
|
| Stormfiends | 60mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. |
|
| Stormvermin | 25mm |
4mm x 2mm: Works well for infantry. (Stack 2pcs of 4mm x 1mm) 5mm x 2mm: Alternative for better stability. 6mm x 2mm or 3mm: Suitable for most standard bases. |
|
| Thanquol on Boneripper | 90 x 52mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Verminlord Corruptor | 120 x 92mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Verminlord Deceiver | 120 x 92mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Verminlord Warbringer | 120 x 92mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| OSSIARCH BONEREAPERS | |||
| Arch-Kavalos Zandtos | 80mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Bone-tithe Shrieker | 90 x 52mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Gothizzar Harvester | 105 x 70mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Immortis Guard | 50mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Katakros, Mortarch of the Necropolis | 120 x 92mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Kavalos Deathriders | 60 x 35mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. |
|
| Liege-Kavalos | 80mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Mortek Crawler | 170 x 105mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Mortek Guard | 25mm |
4mm x 2mm: Works well for infantry. (Stack 2pcs of 4mm x 1mm) 5mm x 2mm: Alternative for better stability. 6mm x 2mm or 3mm: Suitable for most standard bases. |
|
| Mortisan Boneshaper | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Mortisan Soulmason | 40mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. |
|
| Mortisan Soulreaper | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Nightmare Predator | 60mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. |
|
| Necropolis Stalkers | 50mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Soulstealer Carrion | 60mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. |
|
| Vokmortian, Master of the Bone-tithe | 40mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. |
|
| FLESH-EATER COURTS | |||
| Abhorrant Archregent | 40mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. |
|
| Abhorrant Ghoul King | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Abhorrant Ghoul King on Royal Terrorgheist | 130mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Abhorrant Ghoul King on Royal Zombie Dragon | 130mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Chalice of Ushoran | 50mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Corpsemare Stampede | 120 x 92mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Crypt Flayers | 50mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Crypt Ghast Courtier | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Crypt Ghouls | 25mm |
4mm x 2mm: Works well for infantry. (Stack 2pcs of 4mm x 1mm) 5mm x 2mm: Alternative for better stability. 6mm x 2mm or 3mm: Suitable for most standard bases. |
|
| Crypt Haunter Courtier | 50mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Crypt Horrors | 50mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Crypt Infernal Courtier | 50mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Royal Terrorgheist | 130mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Royal Zombie Dragon | 130mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Varghulf Courtier | 60mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. |
|
| LEGIONS OF NAGASH | |||
| Wight King with Black Axe | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Zombie Dragon | 130mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Zombies | 25mm |
4mm x 2mm: Works well for infantry. (Stack 2pcs of 4mm x 1mm) 5mm x 2mm: Alternative for better stability. 6mm x 2mm or 3mm: Suitable for most standard bases. |
|
| NIGHTHAUNT | |||
| Black Coach | 170 x 105mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Bladegheist Revenants | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Cairn Wraith | 25mm |
4mm x 2mm: Works well for infantry. (Stack 2pcs of 4mm x 1mm) 5mm x 2mm: Alternative for better stability. 6mm x 2mm or 3mm: Suitable for most standard bases. |
|
| Chainghasts | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Chainrasp Horde | 25mm |
4mm x 2mm: Works well for infantry. (Stack 2pcs of 4mm x 1mm) 5mm x 2mm: Alternative for better stability. 6mm x 2mm or 3mm: Suitable for most standard bases. |
|
| Dreadblade Harrow | 60 x 35mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. |
|
| Dreadscythe Harridans | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Glaivewraith Stalkers | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Grimghast Reapers | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Guardian of Souls with Nightmare Lantern | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Hexwraiths | 60 x 35mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. |
|
| Knight of Shrouds | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Knight of Shrouds on Ethereal Steed | 75 x 42mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Kurdoss Valentian, the Craven King | 60mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. |
|
| Lady Olynder, Mortarch of Grief | 60mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. |
|
| Lord Executioner | 40mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. |
|
| Mortalis Terminexus | 50mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Mourngul | 60mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. |
|
| Myrmourn Banshees | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Reikenor the Grimhailer | 75 x 42mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Shyish Reaper | 105 x 70mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Spirit Hosts | 50mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Spirit Torment | 40mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. |
|
| Tomb Banshee | 25mm |
4mm x 2mm: Works well for infantry. (Stack 2pcs of 4mm x 1mm) 5mm x 2mm: Alternative for better stability. 6mm x 2mm or 3mm: Suitable for most standard bases. |
|
| Vault of Souls | 50mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| LEGIONS OF NAGASH | |||
| Arkhan the Black, Mortarch of Sacrament | 120 x 92mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Bat Swarms | 50mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Black Coach | 170 x 105mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Black Knights | 60 x 35mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. |
|
| Blood Knights | 60 x 35mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. |
|
| Bloodseeker Palanquin | 120 x 92mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Cairn Wraith | 25mm |
4mm x 2mm: Works well for infantry. (Stack 2pcs of 4mm x 1mm) 5mm x 2mm: Alternative for better stability. 6mm x 2mm or 3mm: Suitable for most standard bases. |
|
| Corpse Cart with Balefire Brazier | 105 x 70mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Corpse Cart with Unholy Lodestone | 105 x 70mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Coven Throne | 120 x 92mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Dire Wolves | 60 x 35mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. |
|
| Fell Bats | 40mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. |
|
| Grave Guard | 25mm |
4mm x 2mm: Works well for infantry. (Stack 2pcs of 4mm x 1mm) 5mm x 2mm: Alternative for better stability. 6mm x 2mm or 3mm: Suitable for most standard bases. |
|
| Hexwraiths | 60 x 35mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. |
|
| Mannfred, Mortarch of Night | 120 x 92mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Morghast Archai | 60mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. |
|
| Morghast Harbingers | 60mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. |
|
| Mortis Engine | 120 x 92mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Nagash, Supreme Lord of the Undead | 130mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Necromancer | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Neferata, Mortarch of Blood | 120 x 92mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Prince Vhordrai | 130mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| The Sepulchral Guard | 25mm |
4mm x 2mm: Works well for infantry. (Stack 2pcs of 4mm x 1mm) 5mm x 2mm: Alternative for better stability. 6mm x 2mm or 3mm: Suitable for most standard bases. |
|
| Skeleton Warriors | 25mm | 4mm x 2mm: Works well for infantry. (Stack 2pcs of 4mm x 1mm) 5mm x 2mm: Alternative for better stability. 6mm x 2mm or 3mm: Suitable for most standard bases. |
|
| Spirit Hosts | 50mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Terrorgheist | 130mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Tomb Banshee | 25mm |
4mm x 2mm: Works well for infantry. (Stack 2pcs of 4mm x 1mm) 5mm x 2mm: Alternative for better stability. 6mm x 2mm or 3mm: Suitable for most standard bases. |
|
| Vampire Lord | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Vampire Lord on Nightmare Steed | 60 x 35mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. |
|
| Vampire Lord on Zombie Dragon | 130mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Vargheists | 50mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Wight King with Baleful Tomb Blade | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| LEGIONS OF NAGASH | |||
| Arkhan the Black, Mortarch of Sacrament | 120 x 92mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Bat Swarms | 50mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Black Coach | 170 x 105mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Black Knights | 60 x 35mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. |
|
| Blood Knights | 60 x 35mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. |
|
| Bloodseeker Palanquin | 120 x 92mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Cairn Wraith | 25mm |
4mm x 2mm: Works well for infantry. (Stack 2pcs of 4mm x 1mm) 5mm x 2mm: Alternative for better stability. 6mm x 2mm or 3mm: Suitable for most standard bases. |
|
| Corpse Cart with Balefire Brazier | 105 x 70mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Corpse Cart with Unholy Lodestone | 105 x 70mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Coven Throne | 120 x 92mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Dire Wolves | 60 x 35mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. |
|
| Fell Bats | 40mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. |
|
| Grave Guard | 25mm |
4mm x 2mm: Works well for infantry. (Stack 2pcs of 4mm x 1mm) 5mm x 2mm: Alternative for better stability. 6mm x 2mm or 3mm: Suitable for most standard bases. |
|
| Hexwraiths | 60 x 35mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. |
|
| Mannfred, Mortarch of Night | 120 x 92mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Morghast Archai | 60mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. |
|
| Morghast Harbingers | 60mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. |
|
| Mortis Engine | 120 x 92mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Nagash, Supreme Lord of the Undead | 130mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Necromancer | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Neferata, Mortarch of Blood | 120 x 92mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Prince Vhordrai | 130mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| The Sepulchral Guard | 25mm |
4mm x 2mm: Works well for infantry. (Stack 2pcs of 4mm x 1mm) 5mm x 2mm: Alternative for better stability. 6mm x 2mm or 3mm: Suitable for most standard bases. |
|
| Skeleton Warriors | 25mm | 4mm x 2mm: Works well for infantry. (Stack 2pcs of 4mm x 1mm) 5mm x 2mm: Alternative for better stability. 6mm x 2mm or 3mm: Suitable for most standard bases. |
|
| Spirit Hosts | 50mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Terrorgheist | 130mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Tomb Banshee | 25mm |
4mm x 2mm: Works well for infantry. (Stack 2pcs of 4mm x 1mm) 5mm x 2mm: Alternative for better stability. 6mm x 2mm or 3mm: Suitable for most standard bases. |
|
| Vampire Lord | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Vampire Lord on Nightmare Steed | 60 x 35mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. |
|
| Vampire Lord on Zombie Dragon | 130mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Vargheists | 50mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Wight King with Baleful Tomb Blade | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| OGOR MAWTRIBES | |||
| Butcher | 50mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Firebelly | 50mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Frost Sabres | 60 x 35mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. |
|
| Frostlord on Stonehorn | 120 x 92mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| FIMIR | |||
| Fimirach Noble | 50mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Fimir Warriors | 50mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| GLOOMSPITE GITZ | |||
| Scaremonger | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Scrapskuttle’s Arachnacauldron | 75 x 42mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Scuttleboss on Gigantic Spider | 60mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. |
|
| Shootas | 25mm |
4mm x 2mm: Works well for infantry. (Stack 2pcs of 4mm x 1mm) 5mm x 2mm: Alternative for better stability. 6mm x 2mm or 3mm: Suitable for most standard bases. |
|
| Shroomancer | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Skitterstrand Arachnarok | 160mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Skragrott, the Loonking | 60 x 35mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. |
|
| Sneaky Snufflers | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Spider Riders | 60 x 35mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. |
|
| Spiker | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Sporesplatta Fanatics | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Squig Gobba | 120 x 92mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Squig Herd | 25mm |
4mm x 2mm: Works well for infantry. (Stack 2pcs of 4mm x 1mm) 5mm x 2mm: Alternative for better stability. 6mm x 2mm or 3mm: Suitable for most standard bases. |
|
| Squig Hoppers | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Stabbas | 25mm |
4mm x 2mm: Works well for infantry. (Stack 2pcs of 4mm x 1mm) 5mm x 2mm: Alternative for better stability. 6mm x 2mm or 3mm: Suitable for most standard bases. |
|
| Troggoth Hag | 120 x 92mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Webspinner Shaman | 25mm |
4mm x 2mm: Works well for infantry. (Stack 2pcs of 4mm x 1mm) 5mm x 2mm: Alternative for better stability. 6mm x 2mm or 3mm: Suitable for most standard bases. |
|
| Webspinner Shaman on Arachnarok Spider | 160mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Zarbag | 25mm |
4mm x 2mm: Works well for infantry. (Stack 2pcs of 4mm x 1mm) 5mm x 2mm: Alternative for better stability. 6mm x 2mm or 3mm: Suitable for most standard bases. |
|
| Zarbag’s Gitz | 25mm | 4mm x 2mm: Works well for infantry. (Stack 2pcs of 4mm x 1mm) 5mm x 2mm: Alternative for better stability. 6mm x 2mm or 3mm: Suitable for most standard bases. |
|
| GITMOB GROTS | |||
| Doom Diver Catapult | 90 x 52mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Doom Diver Catapult Crew with Rope | 60 x 35mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. |
|
| Doom Diver Catapult Crew with Hammer | 25mm |
4mm x 2mm: Works well for infantry. (Stack 2pcs of 4mm x 1mm) 5mm x 2mm: Alternative for better stability. 6mm x 2mm or 3mm: Suitable for most standard bases. |
|
| Doom Diver | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Grot Rock Lobber | 105 x 70mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Grot Rock Lobber Crew | 25mm |
4mm x 2mm: Works well for infantry. (Stack 2pcs of 4mm x 1mm) 5mm x 2mm: Alternative for better stability. 6mm x 2mm or 3mm: Suitable for most standard bases. |
|
| Grot Rock Lobber Orruk Bully | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Grot Shaman | 25mm |
4mm x 2mm: Works well for infantry. (Stack 2pcs of 4mm x 1mm) 5mm x 2mm: Alternative for better stability. 6mm x 2mm or 3mm: Suitable for most standard bases. |
|
| Grot Shaman on Wolf | 60 x 35mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. |
|
| Grot Spear Chukka | 50mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Grot Spear Chukka Crew | 25mm |
4mm x 2mm: Works well for infantry. (Stack 2pcs of 4mm x 1mm) 5mm x 2mm: Alternative for better stability. 6mm x 2mm or 3mm: Suitable for most standard bases. |
|
| Grot Wolf Chariots | 105 x 70mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Grot Wolf Riders | 60 x 35mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. |
|
| Grots | 25mm |
4mm x 2mm: Works well for infantry. (Stack 2pcs of 4mm x 1mm) 5mm x 2mm: Alternative for better stability. 6mm x 2mm or 3mm: Suitable for most standard bases. |
|
| Nasty Skulkers | 25mm | 4mm x 2mm: Works well for infantry. (Stack 2pcs of 4mm x 1mm) 5mm x 2mm: Alternative for better stability. 6mm x 2mm or 3mm: Suitable for most standard bases. |
|
| Snotling Pump Wagons | 105 x 70mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Snotlings | 50mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| GREENSKINZ | |||
| Orruk Boar Chariots | 120 x 92mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Orruk Boarboys | 60 x 35mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. |
|
| Orruk Great Shaman | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Orruk Warboss | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Orruk Warboss with Banner | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Orruk Warboss on War Boar | 60 x 35mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. |
|
| Orruk Warboss on Wyvern | 100mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Orruks | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Rogue Idol | 170 x 105mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| GLOOMSPITE GITZ | |||
| Aleguzzler Gargant | 90 x 52mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Arachnarok Spider with Flinger | 160mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Arachnarok Spider with Spiderfang Warparty | 160mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Boggleye | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Boingrot Bounderz | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Bonegrinder Gargant | 120 x 92mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Brewgit | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Colossal Squig | 120 x 92mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Dankhold Troggboss | 60mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. |
|
| Dankhold Troggoths | 60mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. |
|
| Fellwater Troggoths | 50mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Fungoid Cave-Shaman | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Loonboss | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Loonboss on Giant Cave Squig | 40mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. |
|
| Loonboss on Mangler Squigs | 80mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Loonboss with Giant Cave Squig | 60mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. |
|
| Loonsmasha Fanatics | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Madcap Shaman | 25mm |
4mm x 2mm: Works well for infantry. (Stack 2pcs of 4mm x 1mm) 5mm x 2mm: Alternative for better stability. 6mm x 2mm or 3mm: Suitable for most standard bases. |
|
| Malevolent Moon | 50mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Mangler Squigs | 80mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Mollog | 50mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| (Minions are | |||
| 25mm) |
4mm x 2mm: Works well for infantry. (Stack 2pcs of 4mm x 1mm) 5mm x 2mm: Alternative for better stability. 6mm x 2mm or 3mm: Suitable for most standard bases. |
||
| Mork’s Mighty Mushroom | 50mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Rockgut Troggoths | 50mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| OGOR MAWTRIBES | |||
| Frostlord on Thundertusk | 120 x 92mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Gorgers | 50mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Gnoblar Scraplauncher | 120 x 92mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Gnoblars | 25mm |
4mm x 2mm: Works well for infantry. (Stack 2pcs of 4mm x 1mm) 5mm x 2mm: Alternative for better stability. 6mm x 2mm or 3mm: Suitable for most standard bases. |
|
| Huskard on Stonehorn | 120 x 92mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Huskard on Thundertusk | 120 x 92mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Icebrow Hunter | 50mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Icefall Yhetees | 50mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Ironblaster | 120 x 92mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Ironguts | 40mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. |
|
| Leadbelchers | 40mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. |
|
| Maneaters | 50mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Mournfang Pack | 90 x 52mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Ogor Gluttons | 40mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. |
|
| Slaughtermaster | 105 x 70mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Stonehorn Beastriders | 120 x 92mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Thundertusk Beastriders | 120 x 92mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Tyrant | 50mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| ORRUK WARCLANS | |||
| Ardboys | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Brutes | 40mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. |
|
| Gordrakk, the Fist of Gork | 160mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Gore-gruntas | 90 x 52mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Ironskull’s Boyz | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Megaboss | 60mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. |
|
| Megaboss on Maw-krusha | 160mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Maniak Weirdnob | 60 x 35mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. |
|
| Savage Big Boss | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Savage Big Stabbas | 60 x 35mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. |
|
| Savage Boarboy Maniaks | 60 x 35mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. |
|
| Savage Boarboys | 60 x 35mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. |
|
| Savage Orruk Arrowboys | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Savage Orruk Morboys | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Savage Orruks | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Warchanter | 40mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. |
|
| Wardokk | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Weirdnob Shaman | 40mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. |
|
| Wurrgog Prophet | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| ELDRITCH COUNCIL | |||
| Archmage | 25mm |
4mm x 2mm: Works well for infantry. (Stack 2pcs of 4mm x 1mm) 5mm x 2mm: Alternative for better stability. 6mm x 2mm or 3mm: Suitable for most standard bases. |
|
| Archmage on Steed | 60 x 35mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. |
|
| Archmage on Dragon | 120 x 92mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Drakeseer | 120 x 92mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Loremaster | 25mm |
4mm x 2mm: Works well for infantry. (Stack 2pcs of 4mm x 1mm) 5mm x 2mm: Alternative for better stability. 6mm x 2mm or 3mm: Suitable for most standard bases. |
|
| Swordmasters | 25mm | 4mm x 2mm: Works well for infantry. (Stack 2pcs of 4mm x 1mm) 5mm x 2mm: Alternative for better stability. 6mm x 2mm or 3mm: Suitable for most standard bases. |
|
| FYRESLAYERS | |||
| Auric Hearthguard | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Auric Runefather | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Auric Runefather on Magmadroth | 120 x 92mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Auric Runemaster | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Auric Runesmiter | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Auric Runesmiter on Magmadroth | 120 x 92mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Auric Runeson | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Auric Runeson on Magmadroth | 120 x 92mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| AELF | |||
| Mistweaver Saih | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Tenebrael Shard | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| CITIES OF SIGMAR | |||
| Shadow Warriors | 25mm |
4mm x 2mm: Works well for infantry. (Stack 2pcs of 4mm x 1mm) 5mm x 2mm: Alternative for better stability. 6mm x 2mm or 3mm: Suitable for most standard bases. |
|
| Sisters of the Thorn | 60 x 35mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. |
|
| Sisters of the Watch | 25mm |
4mm x 2mm: Works well for infantry. (Stack 2pcs of 4mm x 1mm) 5mm x 2mm: Alternative for better stability. 6mm x 2mm or 3mm: Suitable for most standard bases. |
|
| Sorceress | 25mm | 4mm x 2mm: Works well for infantry. (Stack 2pcs of 4mm x 1mm) 5mm x 2mm: Alternative for better stability. 6mm x 2mm or 3mm: Suitable for most standard bases. |
|
| Sorceress on Black Dragon | 105 x 70mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Steam Tank | 120 x 92mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| War Hydra | 120 x 92mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Warden King | 25mm |
4mm x 2mm: Works well for infantry. (Stack 2pcs of 4mm x 1mm) 5mm x 2mm: Alternative for better stability. 6mm x 2mm or 3mm: Suitable for most standard bases. |
|
| Wild Riders | 60 x 35mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. |
|
| Wildwood Rangers | 25mm |
4mm x 2mm: Works well for infantry. (Stack 2pcs of 4mm x 1mm) 5mm x 2mm: Alternative for better stability. 6mm x 2mm or 3mm: Suitable for most standard bases. |
|
| CITIES OF SIGMAR | |||
| Anointed | 25mm |
4mm x 2mm: Works well for infantry. (Stack 2pcs of 4mm x 1mm) 5mm x 2mm: Alternative for better stability. 6mm x 2mm or 3mm: Suitable for most standard bases. |
|
| Assassin | 25mm | 4mm x 2mm: Works well for infantry. (Stack 2pcs of 4mm x 1mm) 5mm x 2mm: Alternative for better stability. 6mm x 2mm or 3mm: Suitable for most standard bases. |
|
| Battlemage | 25mm | 4mm x 2mm: Works well for infantry. (Stack 2pcs of 4mm x 1mm) 5mm x 2mm: Alternative for better stability. 6mm x 2mm or 3mm: Suitable for most standard bases. |
|
| Battlemage on Griffon | 120 x 92mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Black Ark Corsairs | 25mm |
4mm x 2mm: Works well for infantry. (Stack 2pcs of 4mm x 1mm) 5mm x 2mm: Alternative for better stability. 6mm x 2mm or 3mm: Suitable for most standard bases. |
|
| Black Ark Fleetmaster | 25mm | 4mm x 2mm: Works well for infantry. (Stack 2pcs of 4mm x 1mm) 5mm x 2mm: Alternative for better stability. 6mm x 2mm or 3mm: Suitable for most standard bases. |
|
| Black Guard | 25mm | 4mm x 2mm: Works well for infantry. (Stack 2pcs of 4mm x 1mm) 5mm x 2mm: Alternative for better stability. 6mm x 2mm or 3mm: Suitable for most standard bases. |
|
| Bleakswords | 25mm | 4mm x 2mm: Works well for infantry. (Stack 2pcs of 4mm x 1mm) 5mm x 2mm: Alternative for better stability. 6mm x 2mm or 3mm: Suitable for most standard bases. |
|
| Celestial Hurricanum | 120 x 92mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Cogsmith | 25mm |
4mm x 2mm: Works well for infantry. (Stack 2pcs of 4mm x 1mm) 5mm x 2mm: Alternative for better stability. 6mm x 2mm or 3mm: Suitable for most standard bases. |
|
| Dark Riders | 60 x 35mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. |
|
| Darkshards | 25mm |
4mm x 2mm: Works well for infantry. (Stack 2pcs of 4mm x 1mm) 5mm x 2mm: Alternative for better stability. 6mm x 2mm or 3mm: Suitable for most standard bases. |
|
| Demigryph Knights | 75 x 42mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Drakespawn Chariots | 120 x 92mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Drakespawn Knights | 60 x 35mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. |
|
| Dreadlord on Black Dragon | 105 x 70mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Dreadspears | 25mm |
4mm x 2mm: Works well for infantry. (Stack 2pcs of 4mm x 1mm) 5mm x 2mm: Alternative for better stability. 6mm x 2mm or 3mm: Suitable for most standard bases. |
|
| Eternal Guard | 25mm | 4mm x 2mm: Works well for infantry. (Stack 2pcs of 4mm x 1mm) 5mm x 2mm: Alternative for better stability. 6mm x 2mm or 3mm: Suitable for most standard bases. |
|
| Executioners | 25mm | 4mm x 2mm: Works well for infantry. (Stack 2pcs of 4mm x 1mm) 5mm x 2mm: Alternative for better stability. 6mm x 2mm or 3mm: Suitable for most standard bases. |
|
| Flagellants | 25mm | 4mm x 2mm: Works well for infantry. (Stack 2pcs of 4mm x 1mm) 5mm x 2mm: Alternative for better stability. 6mm x 2mm or 3mm: Suitable for most standard bases. |
|
| Flamespyre Phoenix | 120 x 92mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Freeguild Crossbowmen | 25mm |
4mm x 2mm: Works well for infantry. (Stack 2pcs of 4mm x 1mm) 5mm x 2mm: Alternative for better stability. 6mm x 2mm or 3mm: Suitable for most standard bases. |
|
| Freeguild General | 25mm | 4mm x 2mm: Works well for infantry. (Stack 2pcs of 4mm x 1mm) 5mm x 2mm: Alternative for better stability. 6mm x 2mm or 3mm: Suitable for most standard bases. |
|
| Freeguild General on Griffon | 120 x 92mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Freeguild Greatswords | 25mm |
4mm x 2mm: Works well for infantry. (Stack 2pcs of 4mm x 1mm) 5mm x 2mm: Alternative for better stability. 6mm x 2mm or 3mm: Suitable for most standard bases. |
|
| Freeguild Guard | 25mm | 4mm x 2mm: Works well for infantry. (Stack 2pcs of 4mm x 1mm) 5mm x 2mm: Alternative for better stability. 6mm x 2mm or 3mm: Suitable for most standard bases. |
|
| Freeguild Handgunners | 25mm | 4mm x 2mm: Works well for infantry. (Stack 2pcs of 4mm x 1mm) 5mm x 2mm: Alternative for better stability. 6mm x 2mm or 3mm: Suitable for most standard bases. |
|
| Freeguild Outriders | 60 x 35mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. |
|
| Freeguild Pistoliers | 60 x 35mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. |
|
| Frostheart Phoenix | 120 x 92mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Gyrobombers | 50mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Gyrocopters | 50mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Hammerers | 25mm |
4mm x 2mm: Works well for infantry. (Stack 2pcs of 4mm x 1mm) 5mm x 2mm: Alternative for better stability. 6mm x 2mm or 3mm: Suitable for most standard bases. |
|
| Helblaster Volley Gun | 90 x 52mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Helstorm Rocket Battery | 90 x 52mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Ironbreakers | 25mm |
4mm x 2mm: Works well for infantry. (Stack 2pcs of 4mm x 1mm) 5mm x 2mm: Alternative for better stability. 6mm x 2mm or 3mm: Suitable for most standard bases. |
|
| Irondrakes | 25mm | 4mm x 2mm: Works well for infantry. (Stack 2pcs of 4mm x 1mm) 5mm x 2mm: Alternative for better stability. 6mm x 2mm or 3mm: Suitable for most standard bases. |
|
| Kharibdyss | 120 x 92mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Longbeards | 25mm |
4mm x 2mm: Works well for infantry. (Stack 2pcs of 4mm x 1mm) 5mm x 2mm: Alternative for better stability. 6mm x 2mm or 3mm: Suitable for most standard bases. |
|
| Luminark of Hysh | 120 x 92mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Nomad Prince | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Phoenix Guard | 25mm |
4mm x 2mm: Works well for infantry. (Stack 2pcs of 4mm x 1mm) 5mm x 2mm: Alternative for better stability. 6mm x 2mm or 3mm: Suitable for most standard bases. |
|
| Runelord | 25mm | 4mm x 2mm: Works well for infantry. (Stack 2pcs of 4mm x 1mm) 5mm x 2mm: Alternative for better stability. 6mm x 2mm or 3mm: Suitable for most standard bases. |
|
| Scourgerunner Chariots | 120 x 92mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| DAUGHTERS OF KHAINE | |||
| Avatar of Khaine | 40mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. |
|
| Blood Sisters | 40mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. |
|
| Blood Stalkers | 40mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. |
|
| Bloodwrack Medusae | 40mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. |
|
| Bloodwrack Shrine | 120 x 92mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Doomfire Warlocks | 60 x 35mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. |
|
| Hag Queen | 25mm |
4mm x 2mm: Works well for infantry. (Stack 2pcs of 4mm x 1mm) 5mm x 2mm: Alternative for better stability. 6mm x 2mm or 3mm: Suitable for most standard bases. |
|
| Hag Queen on Cauldron of Blood | 120 x 92mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Khinerai Heartrenders | 40mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. |
|
| Khinerai Lifetakers | 40mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. |
|
| Morathi, High Oracle of Khaine | 40mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. |
|
| Morathi, the Shadow Queen | 100mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Sisters of Slaughter | 25mm |
4mm x 2mm: Works well for infantry. (Stack 2pcs of 4mm x 1mm) 5mm x 2mm: Alternative for better stability. 6mm x 2mm or 3mm: Suitable for most standard bases. |
|
| Slaughter Queen | 25mm | 4mm x 2mm: Works well for infantry. (Stack 2pcs of 4mm x 1mm) 5mm x 2mm: Alternative for better stability. 6mm x 2mm or 3mm: Suitable for most standard bases. |
|
| Slaughter Queen on Cauldron of Blood | 120 x 92mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Witch Aelves | 25mm |
4mm x 2mm: Works well for infantry. (Stack 2pcs of 4mm x 1mm) 5mm x 2mm: Alternative for better stability. 6mm x 2mm or 3mm: Suitable for most standard bases. |
|
| STORMCAST ETERNALS | |||
| Aetherwings | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Astreia Solbright | 90 x 52mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Aventis Firestrike, Magister of Hammerhal | 100mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Castigators | 40mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. |
|
| Celestant-Prime, Hammer of Sigmar | 100mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Celestar Ballista | 60mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. |
|
| Celestar Ballista Crew | 40mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. |
|
| Celestian Vortex | 65mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Dais Arcanum | 50mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Dracothian Guard Concussors | 90 x 52mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Dracothian Guard Desolators | 90 x 52mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Dracothian Guard Fulminators | 90 x 52mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Dracothian Guard Tempestors | 90 x 52mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Drakesworn Templar | 170 x 105mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Everblaze Comet | 65mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Evocators | 40mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. |
|
| FYRESLAYERS | |||
| Battlesmith | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| The Chosen Axes | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Doomseeker | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Fjul-Grimnir | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Grimwrath Berzerker | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Hearthguard Berzerkers | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Molten Infernoth | 120 x 92mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Vulkite Berzerkers | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| ORDER DRACONIS | |||
| Dragon Noble | 25mm |
4mm x 2mm: Works well for infantry. (Stack 2pcs of 4mm x 1mm) 5mm x 2mm: Alternative for better stability. 6mm x 2mm or 3mm: Suitable for most standard bases. |
|
| Dragon Noble on Steed | 60 x 35mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. |
|
| Dragonlord | 120 x 92mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Dragon Blades | 60 x 35mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. |
|
| SERAPHON | |||
| Bastiladon | 120 x 92mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Chameleon Skinks | 25mm |
4mm x 2mm: Works well for infantry. (Stack 2pcs of 4mm x 1mm) 5mm x 2mm: Alternative for better stability. 6mm x 2mm or 3mm: Suitable for most standard bases. |
|
| Dread Saurian | 280 x 210mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Engine of the Gods | 120 x 92mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Kroxigor | 50mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Lord Kroak | 50mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Razordons | 60 x 35mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. |
|
| Ripperdactyl Riders | 50mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Salamanders | 60 x 35mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. |
|
| Saurus Astrolith Bearer | 40mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. |
|
| Saurus Eternity Warden | 40mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. |
|
| Saurus Guard | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Saurus Knights | 60 x 35mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. |
|
| Saurus Oldblood | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Saurus Oldblood on Carnosaur | 120 x 92mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Saurus Scar-Veteran on Carnosaur | 120 x 92mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Saurus Scar-Veteran on Cold One | 60 x 35mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. |
|
| Saurus Sunblood | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Saurus Warriors | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Skink Handlers | 25mm |
4mm x 2mm: Works well for infantry. (Stack 2pcs of 4mm x 1mm) 5mm x 2mm: Alternative for better stability. 6mm x 2mm or 3mm: Suitable for most standard bases. |
|
| Skink Priest | 25mm | 4mm x 2mm: Works well for infantry. (Stack 2pcs of 4mm x 1mm) 5mm x 2mm: Alternative for better stability. 6mm x 2mm or 3mm: Suitable for most standard bases. |
|
| Skink Starpriest | 25mm | 4mm x 2mm: Works well for infantry. (Stack 2pcs of 4mm x 1mm) 5mm x 2mm: Alternative for better stability. 6mm x 2mm or 3mm: Suitable for most standard bases. |
|
| Skink Starseer | 50mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Skinks | 25mm |
4mm x 2mm: Works well for infantry. (Stack 2pcs of 4mm x 1mm) 5mm x 2mm: Alternative for better stability. 6mm x 2mm or 3mm: Suitable for most standard bases. |
|
| Slann Starmaster | 50mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Stegadon | 120 x 92mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Terradon Riders | 50mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Troglodon | 120 x 92mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| IDONETH DEEPKIN | |||
| Akhelian Allopex | 90 x 52mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Akhelian Ishlaen Guard | 60 x 35mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. |
|
| Akhelian King | 60mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. |
|
| Akhelian Leviadon | 120 x 92mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Akhelian Morrsarr Guard | 60 x 35mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. |
|
| Eidolon of Mathlann, Aspect of the Sea | 100mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Eidolon of Mathlann, Aspect of the Storm | 100mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Isharann Soulrender | 40mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. |
|
| Isharann Soulscryer | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Isharann Tidecaster | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Lotann, Warden of the Soul Ledgers | 40mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. |
|
| Namarti Reavers | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Namarti Thralls | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Volturnos, High King of the Deep | 60mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. |
|
| KHARADRON OVERLORDS | |||
| Aether-Khemist | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Aetheric Navigator | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Arkanaut Admiral | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Arkanaut Company | 25mm |
4mm x 2mm: Works well for infantry. (Stack 2pcs of 4mm x 1mm) 5mm x 2mm: Alternative for better stability. 6mm x 2mm or 3mm: Suitable for most standard bases. |
|
| Arkanaut Frigate | 120 x 92mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Arkanaut Ironclad | 170 x 105mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Brokk Grungsson, Lord-Magnate of Barak-Nar | 50mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Endrinmaster | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Endrinriggers | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Grundstok Gunhauler | 105 x 70mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Grundstok Thunderers | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Skywardens | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| LION RANGERS | |||
| White Lion Chariots | 120 x 92mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| White Lions | 25mm |
4mm x 2mm: Works well for infantry. (Stack 2pcs of 4mm x 1mm) 5mm x 2mm: Alternative for better stability. 6mm x 2mm or 3mm: Suitable for most standard bases. |
|
| MONSTERS OF ORDER | |||
| Carmine Dragon | 100mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| STORMCAST ETERNALS | |||
| Evocators on Dracolines | 90 x 52mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Gavriel Sureheart | 40mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. |
|
| Gryph-hounds | 40mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. |
|
| Judicators | 40mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. |
|
| Knight-Azyros | 50mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Knight-Heraldor | 40mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. |
|
| Knight-Incantor | 40mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. |
|
| Knight-Questor | 40mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. |
|
| Knight-Venator | 50mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Knight-Vexillor | 40mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. |
|
| Knight-Zephyros | 40mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. |
|
| Liberators | 40mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. |
|
| Lord-Aquilor | 90 x 52mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Lord-Arcanum | 40mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. |
|
| Lord-Arcanum on Dracoline | 90 x 52mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Lord-Arcanum on Gryph-charger | 90 x 52mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Lord-Arcanum on Tauralon | 100mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Lord-Castellant | 40mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. |
|
| Lord-Celestant | 40mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. |
|
| Lord-Celestant on Dracoth | 90 x 52mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Lord-Celestant on Stardrake | 170 x 105mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Lord-Exorcist | 40mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. |
|
| Lord-Ordinator Vorrus Starstrike | 40mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. |
|
| Lord-Relictor | 40mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. |
|
| Lord-Veritant | 40mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. |
|
| Neave Blacktalon | 40mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. |
|
| Paladin Decimators | 40mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. |
|
| Paladin Protectors | 40mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. |
|
| Paladin Retributors | 40mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. |
|
| Prosecutors | 40mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. |
|
| Raptor-Prime with Longstrike Crossbow | 40mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. |
|
| Sequitors | 40mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. |
|
| Steelheart’s Champions | 40mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. |
|
| The Farstriders | 40mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. |
|
| Vandus Hammerhand | 90 x 52mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Vanguard-Hunters | 40mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. |
|
| Vanguard-Palladors | 75 x 42mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Vanguard-Raptors | 40mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. |
|
| Vanguard-Raptors with Longstrike Crossbows | 60 x 35mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use two stacks for optimal stability. 10mm x 2mm: Provides a stronger hold. |
|
| SYLVANETH | |||
| Treelord | 105 x 70mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Treelord Ancient | 105 x 70mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Vengeful Skullroot | 105 x 70mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| SYLVANETH | |||
| Alarielle the Everqueen | 160mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Branchwraith | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Branchwych | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Drycha Hamadreth | 105 x 70mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Kurnoth Hunters | 50mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Spirit of Durthu | 105 x 70mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Spite-Revenants | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Spiteswarm Hive | 50mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Sylvaneth Dryads | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| Tree-Revenants | 32mm | 5mm x 2mm: Commonly used size. 8mm x 1.5mm: Provides extra stability, especially for heavier models. |
|
| FORBIDDEN POWER | |||
| Horrorghast | 50mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) For strong hold, a single stack is sufficient. 8mm x 1.5mm 5mm x 2mm: Alternative, use 2-3 magnets per base. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Lauchon the Soulseeker | 90 x 52mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Shards of Valagharr | 105 x 70mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
| Soulscream Bridge | 120 x 92mm | 8mm x 2mm: (Stack 2pcs of 8mm x 1mm) Use three stacks for bases 80mm and larger. 10mm x 2mm: Two magnets for very large bases, such as 130mm. For small gaps use epoxy putty to secure the magnet flush with the base. |
|
Magnet Sizes to Magnetise Warhammer Model Elements
This list covers popular characters and parts that can benefit from magnetisation, ensuring flexibility in assembly and ease of transport. For custom models or unique parts, consider the weight and size of the component to select an appropriately sized magnet.
Please be aware this is simply a guide based on research done through recommendations from other Warhammer enthusiasts. We have not tested each model and their compatibility with a certain magnet.
Every magnet application preference differs from individuals, so we advise researching yourself as well as testing and trialing to see what works for you.
| MODEL TYPE | AREA | SUITABLE MAGNETS SIZES (COMMONLY USED) |
| Infantry | Shoulder/ backpacks | 3mm x 2mm (stack 2pcs of 3mm x 1mm) 3mm x 1mm : If space is limited |
| Wrist joints | 2mm x 1mm | |
| Knights | Arms | 5mm to 6mm in diameter and 1mm to 2mm in thickness. |
| Wrists | 3mm to 4mm in diameter and 1mm in thickness. | |
| Weapons | 4mm to 5mm in diameter and 1mm to 2mm in thickness | |
| Head | 3mm in diameter and 1mm in thickness. | |
| Other small attatcmnents (Accessories, Shields, etc) | 2mm to 3mm in diameter and 1mm in thickness. | |
| Torso | 6mm to 8mm in diameter and 2mm to 3mm in thickness. | |
| Larger Tanks & Vehicles | ||
| Baneblade | Weapons and Turrets | 10mm x 2mm . For longer barrels, consider 12mm x 1mm or smaller diameters like 6mm x 2mm or 3mm x 2mm, depending on the size. |
| Sponsons | 6mm depth adjusted for drilling. | |
| Rogal Dorn | Turrets | 8mm x 1.5mm |
| Sponsons | Mix of 8mm x 1.5mm and 6mm x 2mm | |
| Age of Sigmar Models - Stormcast Eternals, Chaos & Seraphon | ||
| Dracothian Guard & Stardrake | Riders and Weapons | 3mm x 2mm (Stack 2pcs of 3mm x 1mm) |
| Rider and Weapon Options | 3mm x 2mm (Stack 2pcs of 3mm x 1mm) | |
| Archaon | Arms, Weapons, and Head Options | 6mm x 2mm |
| Maggoth Lords | Riders and Weapons | 5mm x 2mm |
| Carnosaurs & Stegadons | Riders | 3mm x 2mm (Stack 2pcs of 3mm x 1mm) |
| Weapons and Platforms | 6mm x 2mm | |
| Special Models | ||
| Ogre Thundertusk | Arm for Vulture/Chaintrap | 5mm x 1mm (N45) |
Magnetised Your Models Already?
We would love to see how you have magnetised your Warhammer army - and any tips you think could be good to share!
Tag us in any photos or videos on our socials @THEFIRST4MAGNETS